BATTERY POWERED ELECTRO PERMANENT MAGNETS
For lifting of single Steel Sheets with min. thickness of 5 mm
Thanks to the integrated rechargeable battery group, this revolutionary electro permanent magnetic beam functions completely autonomously.
A power supply cable is not necessary.
The HBEPP-magnets can be used anywhere, even in areas where no electric power supply is available, and can also be used in combination with e.g. a forklift possible.
The electric pulse of a few seconds is only used to molecularly invert the magnet modules. Then the power drops. The effective force is generated by permanent magnets.
Because the electro permanent magnetic beam does not depend on the electric current, it is 100% safe.
Due to the low power consumption, the rechargeable battery group has an autonomy of approximately 300 cycles. The battery group is charged by means of the built-in charger (230V / 50Hz).
The battery group is equipped with a quick-change system. A BACKUP battery group is optionally available.
ELECTRO PERMANENT MAGNETIC TECHNOLOGY
The electric current is only used to invert the magnetic field, while the effective force is generated by permanent magnets. In the event of a power failure, the magnetic force remains permanently present = 100% safe
Lifting is done in 2 phases, whereby the workpiece is first lifted at a lower preset force, immediately followed by FULLMAG (100% of the total force)
SPC-SYSTEM (SYSTEM PERFORMANCE CHECK)
The electronic system continuously monitors the proper functioning of the magnet. Any abnormal situation is reported immediately and indicated by an error code on the help screen. In this way, errors can be immediately analysed and resolved.
SAFETY FACTOR 3:1
To lift safely, a possible air gap between the contact surface of the magnet, and the steel to be lifted, must be considered. That is why all our magnets are designed with a minimum safety factor of 3: 1 measured at an air gap of 0.4 mm.
2 BUTTON OPERATION
To start the demagnetization cycle, 2 buttons (SAFE + DEMAG) must be pressed consecutively on the remote control.
The status of the magnet is visually indicated by a clear LED lamp block. The load may only be moved when the green lamp lights up continuously!
An inductive proximity switch and associated cam, mounted on the harp shackle of the hoisting chain, prevents accidental demagnetizing in the air.
RADIO REMOTE CONTROL
The magnet is operated from a safe distance. The operator should not come in the immediate vicinity of the load.
With clear safety instructions for the user regarding:
– Maximum weight of the load in function of material thickness
– Maximum wing in function of the deflection of the material.
Select the requested Model to view the Drawing
min - max
min - max
|HBEPP-03-010||1.000||5||500 - 3.000||500 -1.500||4||500|
|HBEPP-06-030||3.000||5||500 - 6.000||500 - 2.500||6||950|
|HBEPP-06-060||6.000||5||500 - 6.000||500 - 2.500||6||950|
|HBEPP-06-090||9.000||5||500 - 6.000||500 - 2.500||6||950|
|HBEPP-09-080||8.000||5||2.500 - 9.000||500 - 3.000||8||1.250|
|HBEPP-09-120||12.000||5||2.500 - 9.000||500 - 3.000||8||1.750|
|HBEPP-12-050||5.000||5||5.000 - 12.000||500 - 3.000||10||1.695|
|HBEPP-12-100||10.000||5||5.000 - 12.000||500 - 3.000||10||2.010|
|HBEPP-12-180||18.000||5||1.700 - 12.000||1.000 - 3.200||16||2.850|
|HBEPP-16-200||20.000||5||2.000 - 16.000||1.300 - 3.500||16||4.650|
|HBEPP-16-250||25.000||5||2.000 - 16.000||1.300 -3.500||16||4.860|